How to Remove Faceplate from Ring Doorbell Pro

Thomas S. Tucci

To remove the faceplate from your Ring Doorbell Pro, start by removing the battery cover. Then, use a small Phillips head screwdriver to remove the two screws that hold the faceplate in place. Finally, gently pull the faceplate away from the doorbell itself.

  • Start with the device powered off
  • Using a Phillips head screwdriver, remove the four screws from the back of the device
  • Carefully separate the faceplate from the back plate
  • There are two wire harnesses connecting the two halves – be sure not to lose or damage them
  • With the faceplate removed, you should now have access to the internal components of your Ring Doorbell Pro

How Do You Remove a Ring Doorbell Pro Faceplate Without a Tool?

If you need to remove your Ring Doorbell Pro faceplate, you can do so without a tool. First, locate the small notch on the bottom of the faceplate. Insert a small flathead screwdriver or other thin object into this notch and apply pressure until the faceplate pops off.

You may need to wiggle the screwdriver back and forth a bit to get started. Once the faceplate is removed, you’ll be able to access the screws that hold on the doorbell itself.

How Do I Remove My Ring Pro Faceplate?

Assuming you are referring to the removable faceplate on the Ring Pro Video Doorbell:To remove the faceplate from your Ring Pro Video Doorbell, start by unscrewing the two screws at the bottom of the device. Next, use a small flathead screwdriver or similar tool to pry off the tab at the top of the faceplate.

With that done, you should be able to gently pull off the faceplate. If it’s being stubborn, try wiggling it back and forth a bit until it comes loose.Once you have removed the faceplate, there are two more screws holding on the battery cover.

Unscrew these and then lift off the cover to access your battery.

How Do You Take the Cover off a Ring Doorbell?

Assuming you would like a step-by-step guide on how to take the cover off a Ring doorbell:1. Begin by unscrewing the two screws at the bottom of the device using a Phillips head screwdriver.2. Gently pull down on the bottom half of the casing until it comes loose from the top half.

Be careful not to lose any of the small internal pieces as you do this.3. With the bottom half of the casing removed, you should now have access to the battery compartment. Remove the batteries and set them aside.

4. Next, locate and remove the small black wire that connects the button assembly to the circuit board. This can be done by gently pulling on it with needle-nose pliers or your fingers.5. With all of these components removed, you should now be able to lift off the top half of the casing and get access to everything inside your Ring doorbell!

What Tool Do I Need to Remove the Ring Doorbell Cover?

Assuming you need to remove the cover for the Ring Doorbell:There are only a few tools you will need in order to remove the cover from your Ring Doorbell. The first is a small Phillips head screwdriver.

You will also need something to pry the cover off with, such as a putty knife or flathead screwdriver. Finally, you may need a pair of needle nose pliers to remove a pesky wire clip holding the doorbell in place.To begin, unscrew the two small screws on either side of the doorbell using your Phillips head screwdriver.

Next, insert your chosen prying tool between the faceplate and housing of the doorbell and apply pressure until the faceplate pops off. If there is a wire clip holding everything in place, use your needle nose pliers to carefully remove it before taking off the faceplate completely. And that’s it!

You should now have access to whatever components inside your Ring Doorbell you needed to get at.

Change Out The Faceplate On The Ring Doorbell Pro

How to Remove Faceplate from Ring Doorbell Pro 2

If you’re having trouble with your Ring Doorbell Pro 2 and need to remove the faceplate, follow these steps:1. Unscrew the four screws on the back of the device using a Phillips head screwdriver.2. Gently pull on the faceplate to release it from the device.

3. If necessary, use a flathead screwdriver to pry off the faceplate. Be careful not to damage the device in the process.4. Once the faceplate is removed, you’ll have access to the doorbell’s internals.

From here, you can troubleshoot any issues you’re having or replace any damaged parts.

How to Remove Ring Faceplate Without Tool

Assuming you’re talking about a door ring faceplate:If the screws are visible, use a screwdriver to remove them. If the screws are not visible, look for a small slot or hole near the edge of the faceplate.

Insert a flathead screwdriver or other thin tool into this slot and twist to release the plate.

How to Remove Faceplate from Ring Doorbell Wired

If you’re having trouble with your Ring Doorbell Wired and need to remove the faceplate, here’s a helpful guide.First, use a screwdriver to remove the two screws that hold the faceplate in place. Be careful not to lose them!

Once the screws are removed, gently pull off the faceplate. You may need to use a small flathead screwdriver or another tool to pry it off if it’s stuck.Now that the faceplate is off, you should be able to see the wires that connect the doorbell to your home’s electrical system.

Disconnect these by unscrewing the terminal screws or cutting the wires (be sure to turn off power first!).Finally, reattach the faceplate by screwing it back into place. Your Ring Doorbell Wired should now be freed from its mount and ready for troubleshooting or replacement.

How to Remove Faceplate from Ring Doorbell 1

If you’re looking to remove the faceplate from your Ring Doorbell 1, there are just a few simple steps to follow. With the help of a small Phillips head screwdriver, you can easily remove the four screws that hold the faceplate in place. Once those screws are removed, the faceplate should simply pop off, revealing the doorbell’s inner workings.

Be sure to keep track of those screws, as they’ll need to be replaced when reattaching the faceplate. And that’s all there is to it! In just a matter of minutes, you can have your Ring Doorbell 1 disassembled and ready for some necessary repairs or upgrades.

Conclusion

If you need to remove the faceplate from your Ring Doorbell Pro, it’s a pretty easy process. First, unscrew the two screws from the bottom of the doorbell. Then, gently pull on the bottom of the faceplate until it pops off.

Be careful not to lose any of the small parts that are attached to the back of the faceplate. Once you have removed the faceplate, you should be able to see four small Phillips head screws. Unscrew these screws and then carefully remove the ring chime unit from behind the doorbell.

You can now access all of the wiring and components inside your Ring Doorbell Pro!

  As an Amazon Associate, I earn from Qualifying Purchases.

Leave a Comment